BMW R1200RS / R1250RS Forum Community › General Forums › Servicing & Maintenance v
Rear Wheel Removal

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Rear Wheel Removal
Terpster Offline
Junior Member
**
Posts: 6
Threads: 3
Joined: Jan 2021
Reputation: 0
Location: Manitoba
#1
04-22-2022, 02:20 PM
Question for all. I have a 2019 RS with the chrome muffler. As I did the rear end service last year I noticed that I could not get the rear wheel out of the way without moving the muffler. Just wondering if anyone has run into the same problem and came up with a solution or do I have just to suffer. Thanks.
Find
Reply
Grumpy Goat Offline
Administrator
*******
Posts: 2,997
Threads: 196
Joined: Feb 2014
Reputation: 334
Location: Houston, Texas, USA
#2
04-22-2022, 03:12 PM
(04-22-2022, 02:20 PM)Terpster Wrote: Question for all. I have a 2019 RS with the chrome muffler. As I did the rear end service last year I noticed that I could not get the rear wheel out of the way without moving the muffler. Just wondering if anyone has run into the same problem and came up with a solution or do I have just to suffer. Thanks.

I always removed the muffler. It is not a problem or difficult. Actually the wheel can be removed without taking the muffler completely off. Just disconnect from the hanger and loosen the pipe connection and rotate and bend away from the wheel and the wheel will be able to be removed.
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Find
Reply
36654 Offline
Senior Member
****
Posts: 387
Threads: 22
Joined: Jul 2020
Reputation: 47
Location: PA, USA
#3
04-22-2022, 03:17 PM
Page 130 of the manual for my 2016 R1200RS says Step 1 of the Rear Wheel Removal is swivel the the muffler (see Page 131)...........
I knocked, but the door was open.......
Central PA: 2016 Lupin RS - Keys and no TPMS
Find
Reply
Ray Offline
Senior Member
****
Posts: 614
Threads: 15
Joined: Sep 2019
Reputation: 191
Location: Saint Louis
#4
04-22-2022, 03:25 PM
(04-22-2022, 03:12 PM)Grumpy Goat Wrote:
(04-22-2022, 02:20 PM)Terpster Wrote: Question for all. I have a 2019 RS with the chrome muffler. As I did the rear end service last year I noticed that I could not get the rear wheel out of the way without moving the muffler. Just wondering if anyone has run into the same problem and came up with a solution or do I have just to suffer. Thanks.

I always removed the muffler. It is not a problem or difficult. Actually the wheel can be removed without taking the muffler completely off. Just disconnect from the hanger and loosen the pipe connection and rotate and bend away from the wheel and the wheel will be able to be removed.
If you want to see Grumpy in action removing the rear wheel - go here:
"A good man always knows his limitations...."
Find
Reply
MrVvrroomm Offline
Senior Member
****
Posts: 271
Threads: 9
Joined: Jun 2019
Reputation: 83
Location: Minnesota USA
#5
04-22-2022, 03:58 PM
(04-22-2022, 03:17 PM)36654 Wrote: Page 130 of the manual for my 2016 R1200RS says Step 1 of the Rear Wheel Removal is swivel the the muffler (see Page 131)...........
nodding, yep
I ride '19 R1250GSA, '23 KTM Duke 890 R, '23 Yamaha Xmax 300
My wife rides '20 R1250GS, '22 KTM Duke 890 GP, '19 Yamaha Xmax 300
Formerly proud Granite Gray '16 R1200RS x2 owners
Find
Reply
Motorhead1977 Offline
Senior Member
****
Posts: 369
Threads: 17
Joined: Sep 2021
Reputation: 64
Location: Albany, New York
#6
04-22-2022, 07:59 PM
Yes, with the stock muffler it must be swiveled out of the way. With the aftermarket can I have I can remove the rear wheel without doing anything with the muffler.
Happiness comes not from what you have, but from enjoying all that you do have no matter how much or little that may be.
Be stubborn with your dream but flexible with your path
Find
Reply
Terpster Offline
Junior Member
**
Posts: 6
Threads: 3
Joined: Jan 2021
Reputation: 0
Location: Manitoba
#7
04-23-2022, 02:11 PM
Thanks for the answers. Take care
Find
Reply
Lee Offline
Debbie's Servant
*****
Posts: 2,103
Threads: 60
Joined: Jun 2018
Reputation: 240
Location: Iowa, US
#8
04-23-2022, 05:56 PM (This post was last modified: 04-24-2022, 07:50 AM by Lee.)
After removing the hanger bolt and loosening the muffler clamp I can remove the muffler in the same time it takes to rotate it.
With the muffler out of the way I get a clear shot at the wheel bolts.
Lee
Iowa, USA
2022 R1250RS White Sport

Past BMWs: 2016 R1200RS x 2,  2011 K1300S x 2,  2003 K1200RS x 2,  1991 K75S x 2,  1987 K75T x 2, 1984 R100RT
Find
Reply
Boxerboy55 Offline
Junior Member
**
Posts: 26
Threads: 4
Joined: Apr 2022
Reputation: 6
Location: UK - Bonnie Scotland
#9
04-23-2022, 06:19 PM
Can off every time. Only 2 screws so only 2 minutes.

Then you’ll want one of these little babies

   
Find
Reply
Lee Offline
Debbie's Servant
*****
Posts: 2,103
Threads: 60
Joined: Jun 2018
Reputation: 240
Location: Iowa, US
#10
04-23-2022, 06:51 PM
(04-23-2022, 06:19 PM)Boxerboy55 Wrote: Can off every time. Only 2 screws so only 2 minutes.

Then you’ll want one of these little babies

I also use one of those.

The newer big hole final drives don't have much of a lip to hold the wheel like the older final drives.
Lee
Iowa, USA
2022 R1250RS White Sport

Past BMWs: 2016 R1200RS x 2,  2011 K1300S x 2,  2003 K1200RS x 2,  1991 K75S x 2,  1987 K75T x 2, 1984 R100RT
Find
Reply
Grumpy Goat Offline
Administrator
*******
Posts: 2,997
Threads: 196
Joined: Feb 2014
Reputation: 334
Location: Houston, Texas, USA
#11
04-23-2022, 09:22 PM
(04-23-2022, 05:56 PM)Lee Wrote: After removing the hanger bolt and loosening the muffler clamp I can remove the muffler in the sam time it takes to rotate it.
With the muffler out of the way I get a clear shot at the wheel bolts.

My rationale and process exactly. Big Grin
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Find
Reply
Terpster Offline
Junior Member
**
Posts: 6
Threads: 3
Joined: Jan 2021
Reputation: 0
Location: Manitoba
#12
04-24-2022, 02:25 PM
Yep I am going to make one of those headless bolts to help with tire repositioning.
Find
Reply
Duckbubbles Offline
Member
***
Posts: 128
Threads: 2
Joined: Jun 2018
Reputation: 27
#13
04-25-2022, 07:36 AM
(04-24-2022, 02:25 PM)Terpster Wrote: Yep I am going to make one of those headless bolts to help with tire repositioning.

I made two. While on the lathe to cut off the heads, I used a file to make the ends bullet shaped to ease wheel fitment. Older rear drives had enough of a lip to position the wheel on installation. I can't see why these rear ends don't have that as well.

Frank
'23 R1250RS, 9000 mi. 1 yr., '03 R1100S BCR #6/200, '85 K100/1100RS- 38 yrs. 331,000 mi., '17R1200RS- 51,054 mi. (gone), '16 R1200RS- 28,322 mi. (gone), '11 R1200RT-30,000 mi. (gone), '05 R1200ST-58,000 mi. (gone), '96 Ducati 900SS/SP-89,000 mi. (gone), 560K+ BMW miles
Find
Reply
Lee Offline
Debbie's Servant
*****
Posts: 2,103
Threads: 60
Joined: Jun 2018
Reputation: 240
Location: Iowa, US
#14
04-25-2022, 08:17 AM
(04-25-2022, 07:36 AM)Duckbubbles Wrote:
(04-24-2022, 02:25 PM)Terpster Wrote: Yep I am going to make one of those headless bolts to help with tire repositioning.

I made two. While on the lathe to cut off the heads, I used a file to make the ends bullet shaped to ease wheel fitment. Older rear drives had enough of a lip to position the wheel on installation. I can't see why these rear ends don't have that as well.

Frank

I didn't get that fancy, I just beveled the one end I touch with my fingers Smile
I put a rubber cap over the threads of the one I carry on trips.
I don't remember the bolt and thread size. I took a wheel bolt to the hardware store to make sure I got the right size.
   
Lee
Iowa, USA
2022 R1250RS White Sport

Past BMWs: 2016 R1200RS x 2,  2011 K1300S x 2,  2003 K1200RS x 2,  1991 K75S x 2,  1987 K75T x 2, 1984 R100RT
Find
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)