Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Valve clearance check
#1
Finally, got this done. All clearances in spec ... just, in some cases. Since the gaps are towards the lower end of the range, with wear the gaps would only increase and at this rate I'd likely not need shims for quite some time (barring some unforeseen event).

Also changed the plugs and made a cool tool to check for TDC. Big Grin

Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Reply
#2
Actually, with wear of the valves, it is more likely that they will tighten up (as the valves tend to "sink" into the seats).

The shims do not wear.
JWMcDonald
Windsor, California
2016 R1200RS (current)
2003 R1150RS (prior)
1978 R80/7 (prior)
1972 R75/5 (prior)
1966 R69S (prior)
Reply
#3
(05-27-2019, 10:35 PM)JWMcDonald Wrote: Actually, with wear of the valves, it is more likely that they will tighten up (as the valves tend to "sink" into the seats).

The shims do not wear.

You are probably right on the first bit ... never thought of that. As the valves wear at the interface with the cylinder head, assuming they wear evenly all around, they will tend to "rise up" and hence decrease the gap at the top in way of the cams.

All parts subject to friction wear. It is just that the cams / shims / followers will most likely wear at a much slower rate than the valve seats.

Thanks for pointing this out. Now I am wondering ... if some of my valves are at the lower end of the range, there is not much leeway for the closing up of the clearances due to valve seat wear ... Undecided

But that is a worry for another day ... TDC as "found" using the DIY tool has some inaccuracy in it as well, and that can also introduce some variance in the clearance measurements, so I am not bothered.
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Reply
#4
quick question on your tool--do i infer correctly that the correct TDC depth is 150mm? Hence the straw with mark? That'd be cool, if so.
Reply
#5
As stated above, valve clearances tend to tighten, no loosen.
I ride '19 R1250GSA, '23 KTM Duke 890 R, '23 Yamaha Xmax 300
My wife rides '20 R1250GS, '22 KTM Duke 890 GP, '19 Yamaha Xmax 300
Formerly proud Granite Gray '16 R1200RS x2 owners
Reply
#6
(06-30-2021, 07:34 AM)mojoguzzi Wrote: quick question on your tool--do i infer correctly that the correct TDC depth is 150mm? Hence the straw with mark? That'd be cool, if so.

Sorry I did not respond sooner - was camping with no cell service. Unfortunately my straw tool fell down a gap in my workbench and I can no longer reach it [easily] or else I'd actually measure it. Sad
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Reply
#7
(07-06-2021, 06:59 AM)Grumpy Goat Wrote:
(06-30-2021, 07:34 AM)mojoguzzi Wrote: quick question on your tool--do i infer correctly that the correct TDC depth is 150mm? Hence the straw with mark? That'd be cool, if so.

Sorry I did not respond sooner - was camping with no cell service. Unfortunately my straw tool fell down a gap in my workbench and I can no longer reach it [easily] or else I'd actually measure it. Sad

Dang! At least it didn't fall into the cylinder Wink
Reply
#8
So...did the valve check yesterday (crappy video to follow later on Brothers, Bikes, & Bourbon YT channel). Some findings and comments:
  • INTAKE
    • .127mm left (spec is .10mm - .17mm)
    • .152mm right
  • EXHAUST
    • .36mm left (spec is .34mm - .41mm)
    • .381mm right
  • Valve covers came off with just some upward-and-outward pressure
  • We could not align a straight-edge, because the new cam design precludes that (wish I'd take a closeup but, oh well)
  • I'm still gonna have the dealer do the check in September when they also replace the air filter and reset the service nag warning.

thanks to all for advice.
Reply
#9
Good findings. Thanks for updating the thread.
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)