Posts: 2,985
Threads: 196
Joined: Feb 2014
Reputation:
331
Location: Houston, Texas, USA
05-25-2020, 08:50 PM
While working on my bike today I noticed this. It looks like something is missing in the indicated area in the first photo, and zoomed in from underneath in the second. Weird.
Do you all have the same detail?
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Posts: 492
Threads: 42
Joined: Jun 2018
Reputation:
57
Location: NC, USA
Whatever it is (was), mine's gone missing too!
I'm guessing some extra bore in the case for some other model?
At first, the plastic piece looked like a gasket.
Posts: 441
Threads: 51
Joined: Jun 2018
Reputation:
139
Location: North Gateway, Phoenix, AZ, USA
05-26-2020, 04:57 AM
(This post was last modified: 05-26-2020, 05:51 AM by darrell.)
Keep in mind my engine has been out of the bike but I trust me mechanic put it back in correctly. My holes in the parts are lined up exactly to the holes. Both the large hole and the small one exactly in front of the side stand are exactly over the holes. The smallest rear one has a zip tie in it to hold that wire likely for the side stand switch and oxygen sensor wire. In between these two holes there is a 3rd hold that has a small screw or bolt which must control exactly how the plastic sits over the holes and tightly against the metal. On your your bike Wayne I can’t tell if you have this screw/bolt. Also notice your cable for the oxygen sensor has some fraying.
Darrell
2016 R1200RS
2022 R1250RT
Posts: 441
Threads: 51
Joined: Jun 2018
Reputation:
139
Location: North Gateway, Phoenix, AZ, USA
05-26-2020, 05:13 AM
(This post was last modified: 05-26-2020, 05:17 AM by darrell.)
Darrell’s bike photo of area in question along with photo of tools used to clean this area[attachment=602][attachment=603]
Darrell
2016 R1200RS
2022 R1250RT
Posts: 175
Threads: 23
Joined: Mar 2020
Reputation:
25
Location: Missouri
I believe those are factory tooling holes to allow jigs or fixtures to be used during the production process.
Posts: 2,985
Threads: 196
Joined: Feb 2014
Reputation:
331
Location: Houston, Texas, USA
(05-26-2020, 04:57 AM)darrell Wrote: In between these two holes there is a 3rd hold that has a small screw or bolt which must control exactly how the plastic sits over the holes and tightly against the metal. On your your bike Wayne I can’t tell if you have this screw/bolt. Also notice your cable for the oxygen sensor has some fraying.
No I don't have that small screw - that missing screw is what made me wonder if something fell off. Will have a second look at the O2 sensor wiring - thanks.
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Posts: 2,985
Threads: 196
Joined: Feb 2014
Reputation:
331
Location: Houston, Texas, USA
(05-26-2020, 04:06 AM)Duccrazydave Wrote: Whatever it is (was), mine's gone missing too!
I'm guessing some extra bore in the case for some other model?
At first, the plastic piece looked like a gasket.
Whew! That is good to know that yours and Darrell's bikes have the same arrangement. Agree that it might we there for some other model. Kind of crappy to keep the gasket there flopping around and doing nothing, though.
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Posts: 2,985
Threads: 196
Joined: Feb 2014
Reputation:
331
Location: Houston, Texas, USA
(05-26-2020, 06:12 AM)Chris216 Wrote: I believe those are factory tooling holes to allow jigs or fixtures to be used during the production process.
Good point, but the gasket and the screw .... I'd think that any jig pin would not need that for temporary use ... strange.
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Posts: 127
Threads: 2
Joined: Jun 2018
Reputation:
27
That plastic piece is actually the forward end of a protective tray that extends to the rear of the transmission for the wiring to the sidestand and 02 sensor.
Frank
'23 R1250RS, 9000 mi. 1 yr., '03 R1100S BCR #6/200, '85 K100/1100RS- 38 yrs. 331,000 mi., '17R1200RS- 51,054 mi. (gone), '16 R1200RS- 28,322 mi. (gone), '11 R1200RT-30,000 mi. (gone), '05 R1200ST-58,000 mi. (gone), '96 Ducati 900SS/SP-89,000 mi. (gone), 560K+ BMW miles
Posts: 2,985
Threads: 196
Joined: Feb 2014
Reputation:
331
Location: Houston, Texas, USA
(05-26-2020, 07:20 AM)Duckbubbles Wrote: That plastic piece is actually the forward end of a protective tray that extends to the rear of the transmission for the wiring to the sidestand and 02 sensor.
Thanks Frank. I must lie down on the floor and take a closer look.
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Posts: 2,092
Threads: 60
Joined: Jun 2018
Reputation:
240
Location: Iowa, US
Both of ours look like Darrell's.
Fastener in place, both wires zip tied together, but not through the hole.
Lee
Iowa, USA
2022 R1250RS White Sport
Past BMWs: 2016 R1200RS x 2, 2011 K1300S x 2, 2003 K1200RS x 2, 1991 K75S x 2, 1987 K75T x 2, 1984 R100RT
Posts: 2,985
Threads: 196
Joined: Feb 2014
Reputation:
331
Location: Houston, Texas, USA
(05-26-2020, 08:48 AM)Lee Wrote: Both of ours look like Darrell's.
Fastener in place, both wires zip tied together, but not through the hole.
Thanks Lee. Now I have to find the fastener and get one.
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Posts: 2,092
Threads: 60
Joined: Jun 2018
Reputation:
240
Location: Iowa, US
(05-26-2020, 07:20 AM)Duckbubbles Wrote: That plastic piece is actually the forward end of a protective tray that extends to the rear of the transmission for the wiring to the sidestand and 02 sensor.
Frank
I found the part but it does not show the fastener in order to know the size.
Lee
Iowa, USA
2022 R1250RS White Sport
Past BMWs: 2016 R1200RS x 2, 2011 K1300S x 2, 2003 K1200RS x 2, 1991 K75S x 2, 1987 K75T x 2, 1984 R100RT
Posts: 2,985
Threads: 196
Joined: Feb 2014
Reputation:
331
Location: Houston, Texas, USA
Brilliant. Thanks Lee. Regarding the bolt - maybe I will drop into the dealer and give them a "test"
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
Posts: 2,092
Threads: 60
Joined: Jun 2018
Reputation:
240
Location: Iowa, US
(05-26-2020, 05:57 PM)Grumpy Goat Wrote: Brilliant. Thanks Lee. Regarding the bolt - maybe I will drop into the dealer and give them a "test"
I could not get a good look at mine.
I'm guessing the cable duct can't go anywhere even without the bolt.
Lee
Iowa, USA
2022 R1250RS White Sport
Past BMWs: 2016 R1200RS x 2, 2011 K1300S x 2, 2003 K1200RS x 2, 1991 K75S x 2, 1987 K75T x 2, 1984 R100RT
Posts: 2,985
Threads: 196
Joined: Feb 2014
Reputation:
331
Location: Houston, Texas, USA
(05-27-2020, 08:29 AM)Lee Wrote: I could not get a good look at mine.
I'm guessing the cable duct can't go anywhere even without the bolt.
Your guess is correct, Lee.
The bolt’s sole function at this point seems to be to (a) stop that end of the cable tray from bending outwards and (b) aligning the hole in the tray with the hole in the block.
Getting a replacement bolt is not a high priority for me.
Sent from my iPhone using Tapatalk
Regards,
Grumpy Goat
2016 BMW R1200RS
2023 Triumph Tiger 900 Rally Pro
|